Tag - panasonic tv repair

CE Tech Tips — September 2021

**NOTICE**
Due to the danger and complexity of electronic equipment repair, the following technical tip is intended for professional reference only. Please refer to manufacturer’s recommendations as Encompass does not guarantee the accuracy, reliability or safety of this information.

Emerson TV, LC320EM2A
Reason for Service
: Powers on with high pitched squeal
and blinking power light.
Solution: Found shorted diode in power supply. D633, 27V/1W. 

Insignia TV, NS-LCD47HD-09
Reason for Service
: No video, backlights okay.
Solution: Replacing U507 on main board fixed set.
(was running very hot)

Panasonic TV, TH42PZ700U
Reason for Service: Dead, seven blink error.
Solution: On SC module look for row of SM FETs.
Check for shorts by lifting on leg of each. Q641-Q654

Samsung TV, UN55ES6100
Reason for Service: Set won’t connect to Internet.
Solution: Replacing the Wi-Fi module fixed set.

Samsung TV, LN55C750R2F
Reason for Service: Set intermittently had video, then went out all together.
Solution: Before replacing T-Con or main, sub crystal X11 from scrap set.  If no good, replace T-Con.

Samsung TV, PCL542R
Reason for Service: Dead set.
Solution: Replaced IC801, IC802 and IC806.

 Sharp TV, LC52D64U
Reason for Service: Dead set. F7000 blown.
Solution: Replaced Q7805, Q7808 and fuse to fix set.

 Sony TV, KV40XBR800
Reason for Service: Shuts down with 6 blink error.
Solution: Found and replaced bad cap C6556, 33uF/160V.

 

Want more tips? Click here to see all electronics and appliance tips!





CE Tech Tips — August 2021

**NOTICE**
Due to the danger and complexity of electronic equipment repair, the following technical tip is intended for professional reference only. Please refer to manufacturer’s recommendations as Encompass does not guarantee the accuracy, reliability or safety of this information.

LG TV, 50PJ350-UB
Reason for Service
: Set starts for a second then shuts off.
Solution: Check/Replace R927 & R929, both 22 ohm/5W.

LG TV, 50PC1DR
Reason for Service: Dead set, 2 blink error.
Solution: Found Q855 in power supply shorted. SD20N60.

Panasonic TV, TH58PX600U
Reason for Service: Dead set,10 blink error.
Solution: Replacing PA board fixed set. 

Samsung TV, PN51D550C1
Reason for Service: Six blink code when set plugged in,
but will not turn on.
Solution: Found bad Y main, then found shorted C5020
on Y main.  Replaced C5020.

 

 

Samsung TV, UN55FH6030FXZA
Reason for Service: Backlight flickers. Cleaned cable ends, no improvement.
Solution: Replacing power supply fixed set.

Sharp TV, LC-60LE600U
Reason for Service: Set will turn on with no picture, sound or backlights.
Solution: First check for bad solder to LED strips.

Vizio TV, VO47L FHDTV10A
Reason for Service: No backlights, audio okay.
Solution: Replaced following: C241, 470uF/35V in power supply, C2 & C3 both 680uF/35V on master inverter board plus 10A fuse F1, and C102 & C103, both 680uF/35V on slave inverter board.

Vizio TV, E401i-A2
Reason for Service
: No backlights.
Solution: Replacing LED driver board fixed set.

 

Want more tips? Click here to see all electronics and appliance tips!





CE Tech Tips — July 2021

**NOTICE**
Due to the danger and complexity of electronic equipment repair, the following technical tip is intended for professional reference only. Please refer to manufacturer’s recommendations as Encompass does not guarantee the accuracy, reliability or safety of this information.

Hisense TV, 50K360G
Reason for Service: Has audio and backlight, but no picture.
Solution: Replaced T-Con. 

LG TV, 32LX1D
Reason for Service: Dead set
Solution: Replacing C127 and C127 restored normal operation.

Panasonic Combo, PVDM2791
Reason for Service: No vertical
Solution: Replaced the following: U451, LA7331, C401, 2.2uF/50V, C402, 470uF/16V, C408, 1uF/50V, and C409, 100uF/35V.

Samsung plasma, HP-R4252
Reason for Service: Picture has red dotted horizontal lines
over 3/4 of the screen.
Solution: Replacing both lower and upper buffers fixed the set.

 

Sony TV, KDL55EX710
Reason for Service: Set shuts down a couple of hours after turning on. 7 blink error.
Solution: Ensure set has good ventilation; might have to replace BAL board.

Vizio TV, E370VLE
Reason for Service: Set won’t start. Logo changes from amber to white, but no B/L, no sound.
Solution: Found D120 on power board was shorted. Used MUR460.

 Vizio TV, M470NV
Reason for Service: Unit powers on, logo goes white then back to amber and set never starts.
Solution: Reflowing U9 on main board fixed the set. 

Westinghouse TV, DW37H1G1
Reason for Service: Set just keeps cycling the colors and will not turn off.
Solution: Unplug set, hold MENU button down while plugging set back in.

 

Want more tips? Click here to see all electronics and appliance tips!





CE Tech Tips — June 2021

**NOTICE**
Due to the danger and complexity of electronic equipment repair, the following technical tip is intended for professional reference only. Please refer to manufacturer’s recommendations as Encompass does not guarantee the accuracy, reliability or safety of this information.

Hitachi TV, L32A403
Reason for Service: Set comes on, works okay for an hour then panel shuts
off; sound and other functions work. Turning the TV off, then back on,
set works again for an hour then repeats.
Solution: Replacing inverter board assembly fixed the set. 

Hitachi TV, 57F59A
Reason for Service
: No video or weak video. No voltage on the
ABL pin of the fly.
Solution: Replaced open RH28. 

Hitachi TV, 57F59A
Reason for Service: HDMI issues, changes colors, snowy picture,
loss of one or more colors, all white, shuts down.
Solution: Replace Signal Board and make sure software
Hitversion is V201 or higher. 

LG TV, 60LS5750
Reason for Service: After set is on for a few minutes, screen has
many red vertical lines, then picture turns off, but audio remains.
Fix: Replacing T-Con fixed the set.

 

Panasonic TV, TC-32LX85
Reason for Service
: No power.
Solution: Found bad photo opto in power supply. PC7000.

Samsung TV, UN40F5500
Reason for Service:
Dead, 2 blink error code.
Solution: Found SM RS802 that feeds the opto was open. Replacing fixed the set. 10 ohm. 

Sony TV, KDL-40V4100
Reason for Service: No video.
Solution: No 12V to T-Con. Replaced U21, (AS15F) on T-Con and replaced F1422/1421 on BU Board.

Sony TV, KV40XBR800
Reason for Service: Dead set.
Solution: Replacing relay RY6502 fixed the set.

 

Want more tips? Click here to see all electronics and appliance tips!





CE Tech Tips — April 2021

**NOTICE**
Due to the danger and complexity of electronic equipment repair, the following technical tip is intended for professional reference only. Please refer to manufacturer’s recommendations as Encompass does not guarantee the accuracy, reliability or safety of this information.

Hitachi TV, 60SDX88B
Reason for Service: Picture displays a pin problem.
Solution: Replacing Q657 fixed this set.

Hitachi TV, 42HDS69
Reason for Service: Set just clicks when powered on.
Solution: Replaced two 3300uF/100V caps in power supply.

Insignia TV, NS42L780A12
Reason for Service: Set had good audio, but no picture because no backlight.
Solution: In the power supply, Q801 and Q802 were shorted, (had bad solder) and R801 was burned.  0.1ohm/2W.

Panasonic TV, TCP50X5
Reason for Service: Dead, may be intermittent.
Solution: Replaced U203 on back side of power supply.

 

Samsung TV, PN51D550C1
Reason for Service: Six blink code when you plug in set, but set will not turn on.
Solution: Determined it was bad Y main, then found shorted C5020 on Y main.  Replaced C5020.

Sony TV, KDL40V2500
Reason for Service: Right side of screen had video strobing; left side no video at all.  Audio okay.
Solution: Found 3 bad caps in power supply, C6204, C6205 and C6207.
Replacing these fixed the set.

Sylvania TV, LC190SL1
Reason for Service: Dead, fuse blown.
Solution: Replaced Q601, Q602, R610, 0.39Ω/2W and D607 zener. Also check D605, D606.

 

Want more tips? Click here to see all electronics and appliance tips!





CE Tech Tips — October 2020

**NOTICE**
Due to the danger and complexity of electronic equipment repair, the following technical tip is intended for professional reference only. Please refer to manufacturer’s recommendations as Encompass does not guarantee the accuracy, reliability or safety of this information.

Emerson TV, LF501EM4
Reason for Service: Dead set, no standby power light.
Solution: Removed the I/R board and found SM C4056 shorted.  Removing bad cap restored normal operation to the set.

Hitachi TV, 57F59A
Reason for Service: Changes colors, snowy picture, loss of one or more colors, all white and shuts down.
Solution: Replace signal board and make sure the firmware is updated. 

LG TV, 47LM6700
Reason for Service: Dead, 3 blink error.
Solution: Replaced a shorted D607.  MUR460

Panasonic TV, TCP42X5
Reason for Service: Dead
Fix: Replaced U203 on backside of Power board.  FAN6755UWMY.

RCA TV, LED46C45RQ
Reason for Service: Set won’t power up.
Solution: Replacing the EEPROM fixed the set.  U16

Samsung TV, PN64E8000GFXZA
Reason for Service: Dead set, fuse blown.
Solution: Repaired power board by replacing QS802 & QS804.  Examine whole board for bad solder and resolder as necessary.

Vizio TV, E390-A1
Reason for Service: LED backlights will not come on.
Solution: Replacing IC U403 fixed the set.

Zenith, 9-1302 module
Reason for Service: Dead, nothing.
Solution: Resoldered jumper next to Elect Cap CX3452.  Fixed set.

Want more tips? Click here to see all electronics and appliance tips!